Combohead Mallet

Combohead Malletvideo
Combohead Mallet Introduction The Combohead Mallet is a combination of a carvers mallet and a joiners mallet. I made a couple of videos early on when I first made the discovery of what is now the official Combohead Mallet design and every time I get asked if I’m going to make any to sale or do I have a template....

Kids Activity table

Kids Activity Table with Storage Plan
We needed a place for the kids to keep all of their arts and crafts supplies and off the top of the fridge, off the dinning room table, and even off the floor. With three boys things can get a bit messy and disorganized, so we needed a solution. We made this activity table... Tools used in this project: Table...

Make A Pedal Board With Plywood

I made a pedal board completely from plywood and wooden dowel rods, no screws. Check out how I made it. Keep reading.... I was asked to make a pedal board and without knowing much about pedals let alone pedal boards I had some research to do. I looked online at some different designs and decided to make it out...

DIY Desk and Organization

DIY Desk and Organizationvideo
Introduction Not too long ago I made a table and chair for my kids to use as a place to do arts and crafts as well as a place for my oldest son to do homework. Since then we’ve had another boy start school and soon we’ll have all three in school, so I figured I better make the other...

Pocket Hole Blanket Chest

Pocket Hole Blanket Chestvideo
Pocket Hole Blanket Chest - One Day Build Introduction In this one day project build I'll show you how to build a pocket hole blanket chest using readily available materials that anyone can do. So, in the middle of trying to stay organized with all the kids stuff inside and out I also need to think about things that my...

Drill Charging Station with Air Tool Storage AND Dust Free Bins

After rearranging my shop a little bit, I lost my drill charging station location due to hanging a cabinet in it's place. So, the only logical thing to do was to build a new one. Keep reading for more... My process was a little different throughout this project, whereas I normally start a project with Sketch-up. This time around...

Outfeed/Assembly Table: Part 1 – The Design

Outfeed/Assembly Part 1
For a while now I'v been meaning to rebuild my outfeed/assembly table due to the fact that it wasn't documented with video or plans when I made it a couple of years ago. So, now's the time to document it and make some changes that will improve the overall use. Watch the Video Here I started out planning...

Garage Organization and Bike Rack

Garage Organization and Bike Rack Thumbnailvideo
Garage Organization and Bike Rack Introduction By now you’re probably aware that I’m a little bit OCD when it comes to organization and tidiness. I used to say everything has a home or a place in and around the house without even thinking about it, but now that I have three boys it is a wee bit harder to keep things...

Kids Activity Chair

Kids activity chair
Not too long ago I made an activity table for my kids and I just recently made matching chairs to go along with it. The table and chairs both have storage for just about anything you want to store in them. Take a look... The first thing I did was breakdown the plywood according to the plans (get the...

Outfeed Assembly Table: Part 2 – The Build

This is part two, the build, of the Outfeed/Assembly Table project. Once I got started on this build I didn't want to stop until it was done. The improved workflow and efficiency this table provides was much needed in the shop, but getting there was challenging... This project was looong overdue. I have been needing more storage and organization...

Knock Down Stool

Knock Down Stool - Mainvideo
Knock Down Stool GET THE PLANS HERE The Design I’ve had the design for this stool idea for a while now, I’m just now getting around to actually making it. The design itself is simple, but the fact that it has much more potential as other furniture is interesting. One main thing I wanted in this project was to make it functional...

Multipurpose Shop Cart

Multipurpose Shop Cart plan
I had a problem in the shop and we solved it... Continue reading to find out how. Click here to watch the build video! I noticed when I used the bandsaw, lathe, table saw, miter saw, jointer, planer, drill press... ok, all of my tool stations that I needed a place to stack the pieces I was working...

Kids Picnic Table

Kids Picnic Table Plan
With Spring here and Summer approaching quickly, I figured an outdoor project was in order. My kids had a small picnic table they used quite a bit, but it was falling apart. They like to eat outside when the weather is nice and so as the woodworking daddy that I am, I made another one. Keep reading... This project...